BTC Spectre MKII Bluetooth Mosfet for V2 Gearboxes DISC

BTC Spectre MKII Bluetooth Mosfet for V2 Gearboxes DISC

SKU: MOS002

Availability: Out of stock

BTC Spectre MKII Bluetooth Mosfet For V2 Gearboxes

Details

This new BTC Mosfet has the latest advanced technology in airsoft electronics. This can handle power surges up to 9000 watts and even run on car batteries, is fully computerized with hi-speed dual ARM Cortex-M0 and PIC18F26K22 microprocessors, has multiple internal layers of heavy copper traces for greater current capacity, has a short circuit detection and voltage spike suppression circuits to protect the controller and also has smart thermal management that reduces heat build-up during sustained firing on certain settings.

This has a smartphone Bluetooth interface, which is the quickest and most versatile method of programming AEGs. No complex trigger inputs or opening the AEG. Program your AEG mid-skirmish in seconds without any tools or manual, just your smartphone only. This has a user-programmable passcode and a shortened signal range, prevents any unauthorized setting changes. No need to "pre-connect" to the Spectre in the smartphone's settings. It is accessed instantly from within the app.

The essential app for techs reports battery voltage, current draw, and FET temperature. Basically a "wireless multimeter". It also reports timing of shot cycles and RoF, which helps to fine-tune the AEG to achieve the best possible cycle rate. It also displays diagnostic functions that display which microswitches are pressed in real-time and also what error has occurred, and it records total number of shots fired since the battery was connected and also for each trigger pull.

The Mosfet Trigger eliminates damaging electrical arcing of the trigger switch contacts and has lower resistance compared to mechanical switching, increasing motor current. This is driven by dual IRF671812PBF, a compact yet powerful next-gen Mosfet.

This Mosfet also has dynamic braking, which eliminates the motor spin-down time to prevent the piston from over-traveling. This assists in keeping the piston properly reset to reduce stress on the gearbox and prevents double firing on semi-fire in extremely high RoF setups.

This also has cycle completion, which makes the gearbox always complete the last cycle regardless of when the trigger is released. This assists in keeping the piston properly reset to reduce stress on the gearbox and makes the motor always have the smoothest and most consistent startup. This allows the anti-reversal latch to be removed.

All three fire select positions can be individually configured, for a total of 729 (9x9x9) possible configs.
Available options for each selector position:

  • Safe
  • Semi fire
  • Auto fire
  • Burst [non-interruptible]
  • Burst [interruptible]
  • Burst/Auto hybrid [burst non-interruptible]
  • Burst/Auto hybrid [burst interruptible]
  • Semi/Auto hybrid
  • Semi/Auto ramping

    The non-interrupt burst completes a burst even if the trigger is released, whereas interruptable stops mid-burst.

Burst modes can be programmed to fire 2 - 10 shots per burst. Each selector can have different burst amounts.
"Burst/Auto hybrid" fires in burst and switches to full auto if the trigger remains held down.
Hybrid modes can be programmed to have no transition delay or a 0.2s - 1s delay.
"Semi/Auto ramping" fires in semi and switches to full auto if the trigger is rapidly tapped.

This has a hardware semi-only lock that can only be enabled/disabled by using a soldering iron to remove/bridge a solder jumper. This conforms to semi-only laws that forbid AEGs with readily accessible means of bypassing semi-only.

This also has a realistic RoF control where both fire select positions can be individually configured with a different RoF. Every cycle runs at full speed and pauses between each shot to reduce the RoF. This provides the most realistic feel and sound compared to any other forms of RoF reduction.

The adjustable pre-cocking stops the piston in a compressed state, so the next shot is near-instantaneous. The pre-cocking is fully adjustable and thus also compatible with short-stroked pistons. This offers improved realism and trigger response for sniper or low RoF builds.

After a semi or burst fire, the adjustable firing interval can ignore trigger inputs for a certain amount of time. Programmable up to 1s. This helps restrict rapid firing in specialized builds, such as limiting a sniper build to firing one shot per second. Lower intervals can also help prevent accidental "bump firing" on semi when using a feather trigger.

This also monitors LiPo and LiFePO4 batteries to cut-off power before over discharge occurs. Simply set the number of cells and the controller will use the proper cut-off voltage.

The programmable digital fuse has a sensor-based current monitoring, which negates the need for a physical fuse. The cut-off threshold is fully adjustable to help protect low-output batteries from over-current damage.

This also eliminates the trigger jam normally caused by the cut-off lever stopping at a certain position. The cut-off lever mechanism is no longer needed, which greatly reduces the chances of semi-fire related issues. The anti-reversal latch can also be removed to make gearbox reassembly much easier.

This is also fully compatible with Airsoft System's hop up sensor unit to prevent firing when the mag is empty.

These generally require a level of technical skill to fit properly so we do advise you have it fitted by a competent technician.

Any questions on compatibility, installation or if you would like one of our in house techs to fit the parts for you, please email us on [email protected] or call us on 01293 525880

More Information

Manufacturer BTC
SKU MOS002

Reviews

Write Your Own Review
You're reviewing: BTC Spectre MKII Bluetooth Mosfet for V2 Gearboxes DISC
Loading...

You submitted your review for moderation.